Teradek Bolt 1000 XT Deluxe Kit with One Transmitter, Two Receivers and Panel Array (Gold Mount)

Teradek Bolt 1000 XT Deluxe Kit with One Transmitter, Two Receivers and Panel Array (Gold Mount)

Teradek Bolt 3000 XT SDI/HDMI Deluxe Kit with One Transmitter, Two Receivers (V-Mount)

Teradek Bolt 3000 XT SDI/HDMI Deluxe Kit with One Transmitter, Two Receivers (V-Mount)

Teradek Bolt 3000 XT SDI/HDMI Wireless TX/RX Deluxe Kit (Gold Mount)

  • Up to 3000' Range Line of Sight
  • Supports up to 1080p60 Resolution
  • 3G-SDI/HDMI Inputs/Outputs
  • Cross Conversion
Regular Price $18,995.01 Special Price $16,885.00
SKU
WTSTEK143

This Teradek Bolt XT 3000 SDI/HDMI Wireless TX/RX Deluxe Kit includes one transmitter and one receiver with installed passthrough Gold mount battery plate, a panel array antenna, plus a variety of accessories. This enables you to immediately start transmitting up to 1080p60 video from either an SDI or HDMI source. The transmitter/receiver pair features a 3000' line-of-site transmission distance when used together, and you can send and receive visually lossless 3G-video signals from a Bolt 3000 transmitter with zero latency. The transmitter features a loop out SDI connector so you can feed your on-camera monitor. The included panel array antenna is directional for improved signal reliability in one direction when compared to the performance of the included omni-directional antennas.

The receiver has a factory-installed passthrough Gold mount battery plate system that features a male Gold mount battery plate on one side of the receiver, and a female Gold mount battery plate on the other side of the receiver. The receiver also features both an SDI and HDMI output. The system supports digital SD and HD signals. Although the inputs and outputs support a variety of HD signals in both 50 and 60 Hz standards, 480i and 576i & 480p and 576p are only available through the HDMI output. You can transmit up to a total of four receivers, and either Bolt 3000, Sidekick II, or 703 Bolt receivers are compatible. The built-in AES 128-bit encryption helps to keep your transmitted video safe from prying eyes. Accessory arm and NATO mounts provide mounting options, and the SKB case protects your gear during transport and storage.

Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Transmitter

With the Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Transmitter you can transmit visually lossless 3G video signals to a Bolt 3000 receiver with zero latency. The Bolt XT is also compatible with the Sidekick II and 703 Bolt. The transmitter unit itself can be secured to a camera or other SDI/HDMI video source via a built-in 1/4"-20 threaded hole, as well as two M3 threaded holes. The included antennas provide a powerful signal that can travel up to 3000' line-of-sight.

A shoe mount is included for attaching to cameras without 1/4"-20 threads. For convenience, both a standard BNC cable and HDMI cable are included so you can plug in right out of the box. Power can be provided using the integrated 2-pin connector via the included D-Tap power cable. The transmitter supports up to four receivers and built-in AES 128 encryption protects your video from prying eyes, while noise rejection helps keep your video clean even when working around 2.4 and 5.8 GHz signals.

Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Receiver

With the Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Receiver you can receive visually lossless 3G-video or HDMI signals from a Bolt 3000 transmitter with zero latency. The receiver unit itself can be secured via built-in 3/8"-16 M3 threaded holes or the built-in NATO rail.

A light stand adapter is included for mounting on stands. For convenience, a standard HDMI cable is included so you can plug in right out of the box. Power can be provided using the integrated 2-pin connector. A D-Tap power cable is included for attaching to a battery. The receiver can share the transmitter with up to three other receivers. It features built-in AES-128 encryption that protects your video from prying eyes, while noise rejection helps keep your video clean even when working around 2.4 and 5.8 GHz signals.

Wooden Camera Ultra Arm Mini Monitor Mount (1/4"-20 to 1/4"-20)

The 1/4"-20 to 1/4"-20 Ultra Arm Mini Monitor Mount from Wooden Camera is a robust and compact articulating arm with 25mm ball joints. Approximately 5" in length from end to end, the Ultra Arm Mini is designed for keeping a monitor or other accessory close to the camera while providing the full range of ball joint articulation. A lever in the center locks both ball joints, and the mounting points on the ends attach to your gear easily at the turn of integrated tightening knobs. Both ends feature rubber pads for more secure support.

The Ultra Arm system is interchangeable. Wooden Camera offers a variety of optional end points that install into the ball sockets of the arm. These include NATO clamps, NATO rails, shoe mounts, super clamps, and extensions to add between two of these arms. There is even a Preston mounting bracket. Additionally, the system is compatible with many third-party 25mm ball mount systems.

Wooden Camera NATO Lock Kit

Quickly secure and detach accessories from your camera rig by adding this NATO Lock Kit from Wooden Camera. The rail attaches to your camera or cage system using the included 1/4"-20 or 3/8"-16 screws while the clamp attaches to the accessory itself via an additional set of 1/4"-20 and 3/8"-16 screws. The rail and clamp are compatible with other NATO standard accessories from RED, Zacuto, and other 3rd party manufacturers.

Teradek Antenna Array for Bolt Receiver

This Antenna Array from Teradek is a panel antenna designed to enhance wireless video transmission to Bolt receivers. This MIMO (Multiple In/Multiple Out) antenna focuses the RF signal and reduces interference, producing a more resilient transmission. It offers a boost in reception but does not increase the maximum transmission range.

The panel array is composed of 3x16 dBi and 2x14 dBi antennas and operates in the 5.1 to 5.8 GHz frequency range. The antenna comes with a mounting bracket, light stand adapter, and five cables.

More Information

Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Transmitter

With the Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Transmitter you can transmit visually lossless 3G video signals to a Bolt 3000 receiver with zero latency. The Bolt XT is also compatible with the Sidekick II and 703 Bolt. The transmitter unit itself can be secured to a camera or other SDI/HDMI video source via a built-in 1/4"-20 threaded hole, as well as two M3 threaded holes. The included antennas provide a powerful signal that can travel up to 3000' line-of-sight.

A shoe mount is included for attaching to cameras without 1/4"-20 threads. For convenience, both a standard BNC cable and HDMI cable are included so you can plug in right out of the box. Power can be provided using the integrated 2-pin connector via the included D-Tap power cable. The transmitter supports up to four receivers and built-in AES 128 encryption protects your video from prying eyes, while noise rejection helps keep your video clean even when working around 2.4 and 5.8 GHz signals.

  • Backward compatible with Teradek's universal receivers Sidekick II and 703 Bolt, which can receive Bolt 3000 XT signals up to 300' away
  • HDMI and 3G-SDI inputs, with 3G-SDI loop-through output on transmitter
  • SDI ancillary data support for metadata, timecode, and start/stop flags from certain camera manufacturers
  • 1/4"-20 and M3 mounting points

Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Receiver

With the Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Receiver you can receive visually lossless 3G-video or HDMI signals from a Bolt 3000 transmitter with zero latency. The receiver unit itself can be secured via built-in 3/8"-16 M3 threaded holes or the built-in NATO rail.

A light stand adapter is included for mounting on stands. For convenience, a standard HDMI cable is included so you can plug in right out of the box. Power can be provided using the integrated 2-pin connector. A D-Tap power cable is included for attaching to a battery. The receiver can share the transmitter with up to three other receivers. It features built-in AES-128 encryption that protects your video from prying eyes, while noise rejection helps keep your video clean even when working around 2.4 and 5.8 GHz signals.

  • The receiver includes built-in cross conversion and Teradek's proprietary software utilities including a manual frequency selection tool, 3D LUT engine, and a 5 GHz spectrum analyzer to keep an eye on interference in your area.
  • The receiver features an HDMI output as well as dual 3G-SDI outputs.
  • An integrated NATO rail on the receiver along with several M3 mounting points and an ARRI-compatible 3/8"-16 threaded hole with locating pin holes provide multiple mounting options.
  • SDI ancillary data support for metadata, timecode, and start/stop flags from certain camera manufacturers.
  • Five included antennas for the receiver enable it to pick signals up with clarity.

 

Wooden Camera Ultra Arm Mini Monitor Mount (1/4"-20 to 1/4"-20)

The 1/4"-20 to 1/4"-20 Ultra Arm Mini Monitor Mount from Wooden Camera is a robust and compact articulating arm with 25mm ball joints. Approximately 5" in length from end to end, the Ultra Arm Mini is designed for keeping a monitor or other accessory close to the camera while providing the full range of ball joint articulation. A lever in the center locks both ball joints, and the mounting points on the ends attach to your gear easily at the turn of integrated tightening knobs. Both ends feature rubber pads for more secure support.

The Ultra Arm system is interchangeable. Wooden Camera offers a variety of optional end points that install into the ball sockets of the arm. These include NATO clamps, NATO rails, shoe mounts, super clamps, and extensions to add between two of these arms. There is even a Preston mounting bracket. Additionally, the system is compatible with many third-party 25mm ball mount systems.

Key Features

  • Full-range ball joint articulation
  • Integrated tightening knobs
  • Rubber pads
  • Interchangeable end points support optional NATO clamps, NATO rails, shoe mounts, super clamps, length extensions, and more (see Accessories tab)
  • Also compatible with third-party 25mm ball mount systems

 

Wooden Camera NATO Lock Kit

Quickly secure and detach accessories from your camera rig by adding this NATO Lock Kit from Wooden Camera. The rail attaches to your camera or cage system using the included 1/4"-20 or 3/8"-16 screws while the clamp attaches to the accessory itself via an additional set of 1/4"-20 and 3/8"-16 screws. The rail and clamp are compatible with other NATO standard accessories from RED, Zacuto, and other 3rd party manufacturers.

 

Teradek Antenna Array for Bolt Receiver

This Antenna Array from Teradek is a panel antenna designed to enhance wireless video transmission to Bolt receivers. This MIMO (Multiple In/Multiple Out) antenna focuses the RF signal and reduces interference, producing a more resilient transmission. It offers a boost in reception but does not increase the maximum transmission range.

The panel array is composed of 3x16 dBi and 2x14 dBi antennas and operates in the 5.1 to 5.8 GHz frequency range. The antenna comes with a mounting bracket, light stand adapter, and five cables.

  • Boosts wireless video transmission
  • Focuses wireless signal and reduces interference
  • 5.1-5.8 GHz frequency range
  • Array of 3x16 dBi and 2x14 dBi antennas

 

Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Transmitter Specs

Transmitter
More Information
Construction Milled aluminum (chassis) and regulation-compliant PCB
Video Inputs SDI: 1 x BNC (75 Ohm), 3G/HD/SD
HDMI: 1 x HDMI type A receptacle
Video Outputs SDI: 1 x BNC (75 Ohm), 3G/HD/SD, loop through
Color Sampling SDI: YCbCr 4:2:2, 10-bit (8-bit when format conversion is enabled)
HDMI: RGB 4:4:4, 8-bit
Latency <0.001 seconds (Tx to Rx without format conversion)
Supported Resolutions 1080p: 60/59.94/50/30/29.97/25/24/23.98
1080PsF: 30/29.97/25/24/23.98
1080i: 60/59.94/50
720p: 60/59.94/50
480i: 59.94
576i: 50
Video Processing Compression
Visually lossless

Color Correction
CDL/1024 1D LUT (supports 10-bit color)
33x33x33 3D LUT (supports 10-bit color)
Audio Compression 48 kHz, 24-bit PCM
Audio Input Embedded
Interfaces Switches: On/Off and Reset
Desktop App: Feature-rich Bolt Manager application for Mac OS X and Windows
USB Interface Functionality: Upgrade via mini-USB
Wireless Non-DFS Frequencies
  • UA: 5.19 to 5.23 GHz, 5.755 to 5.795 GHz
  • EU & JP: 5.19 to 5.23 GHz

DFS Frequencies
  • US: 5.27 to 5.55 GHz and 5.67 GHz
  • EU & JP: 5.27 to 5.67 GHz
RF Power 17 dBm EIRP
Encryption AES-128
Range Up to 3000' / 914.4 m line of sight
Unicast Multicast Unicast / Multicast
Noise Rejection Can coexist with WiFi and 5 GHz cordless phones
Power Input 2-pin connector
7 to 17 VDC
Power Consumption Nominal 7.3 W (measured at 1080p60)
Operating Temperature 32 to 104°F / 0 to 40°C
Mountable 1 x 1/4"-20 threaded mounting hole
2 x M3 threaded mounting holes
Dimensions 0.95 x 2.6 x 4.47" / 2.41 x 6.6 x 11.35 cm
Weight 8 oz / 226 g

Teradek Bolt 3000 XT 3G-SDI/HDMI Wireless Receiver Specs

Wireless
Wireless Range 3000' / 914.4 m
Channel Bandwidth 40 MHz, 20 MHz
Frequency Range Non-DFS Frequencies
US, JP, EU: 5.19 to 5.23 GHz
US: 5.75 to 5.79 GHz
DFS Frequencies
US, JP, EU: 5.27 to 5.67 GHz
US: 5.27 to 5.55 GHz
Latency < 1 ms
RF Power 17 dBm
Wireless Video Compression Uncompressed

Interfaces
Antenna Ports 5 x RP-SMA Female
Video Connectors 1 x BNC (3G-SDI) Output
1 x HDMI (HDMI 1.4) Output
Other I/O 1 x USB Mini-B USB 3.1 Gen 1 Input
HDCP Support None
Embedded Audio HDMI: 2-Channel
SDI: 2-Channel
Encryption 128-Bit AES

Format Support
Broadcast System Compatibility NTSC, PAL
Video Format SDI/BNC:
1080p 4:2:2 YCC 8-Bit at 23.98, 24, 25, 29.97, 30, 50, 59.94, 60 fps
1080PsF 4:2:2 YCC 8-Bit at 23.98, 24, 25, 29.97, 30 fps
1080i/720p 4:2:2 YCC 8-Bit at 50, 59.94, 60 fps
576i/480i
HDMI:
1080p 4:4:4 RGB 8-Bit at 23.98, 24, 25, 29.97, 30, 50, 59.94, 60 fps
1080PsF 4:4:4 RGB 8-Bit at 23.98, 24, 25, 29.97, 30 fps
1080i/720p 4:4:4 RGB 8-Bit at 50, 59.94, 60 fps
576p at 50 fps
480p at 59.94 fps
576i/480i
Audio Format 2-Channel 24-Bit 48 kHz PCM Audio
Timecode Yes
LUT Support 1024 1D LUT
17x17x17 3D LUT

Display
Panel Type OLED

Power
Built-In Battery None
Power Connector 1 x 2-Pin LEMO (7 to 28 VDC) Input
Power Consumption (8.5 W)

Environmental
Operating Temperature 32 to 104°F / 0 to 40°C

General
Mounting 1 x M3 Female
1 x 3/8"-16 Female
Materials Aluminum, PCB
Dimensions 5.43 x 3.5 x 0.94" / 138 x 89 x 24 mm (Without Antennas)
Weight 13.26 oz / 376 g (Without Battery Plate)

Wooden Camera Ultra Arm Mini Monitor Mount (1/4"-20 To 1/4"-20) Specs

Top Mount 1/4"-20 Male
Bottom Mount 1/4"-20 Male
Points of Articulation 2
Maximum Length 5" / 12.7 cm
Weight 4.8 oz / 136 g

Wooden Camera NATO Lock Kit Specs

Compatibility RED Swat rails
Zacuto Z-rails
Other 3rd party NATO products
Dimensions 1.9 x 1.9 x 0.7" (47.2 x 47.2 x 18.3 mm)
Weight 0.1 lb (50 g)

Teradek Antenna Array For Bolt Receiver Specs

Connector RP-SMA plug
Frequency Range 5.1-5.8 GHz
Antenna Gain 3x16 dBi
2x14 dBi
Protocol Support 802.11n (MIMO standard)
Material of Construction UV-protected plastic, aluminum alloy
Dimensions (LxWxD) Antenna: 13.8 x 13.8 x 1.3" (35.0 x 35.0 x 3.2 cm)
Weight Antenna: 2.5 lb (1.1 kg)
More Information

General

  • 1 x Panel Antenna Array 5GHz 3x16dBi 2x 14dBi Black
  • 1 x Protective SKB Case - military-standard waterproof hard case with custom foam (13.5in x 9.5in x 6.5in - 34.29cm x 24.13cm x 16.51cm)
  • 1 x Wooden Camera Ultra Arm Mini Monitor Mount (1/4-20 to 1/4-20) with Arm Ball (3/8-16)
  • 1 x Wooden Camera NATO Lock Kit
  • 1 x Teradek Vinyl Zipper Bag 250x150mm
  • 1 x Hex L Key 2.5 mm size 3-5/6 inch length
  • 1 x Hex L key 3/16inch x 2 13/16inch length
  • 2 x Passthrough Gold Mount plate factory-installed to each RX: 1 Gold Mount (female) Battery Plate 14.4V on one side of RX and 1 Gold Mount (male) Battery Plate on the other side

Transmitter

  • 1 x 2-pin Connector to PowerTap 18 inch Cable
  • 1 x Hot Shoe Adapter (1/4"-20 inch)
  • 2 x Antenna 2dBi WiFi 2.4/5.8 GHz
  • 1 x USB 2.0 Cable (A-Male to Mini-B)
  • 1 x HDMI 18in Cable (Type A to Type A)
  • 1 x SDI (BNC to BNC) Cable 10 inch

Receiver

  • 1 x Lightstand Adapter (3/8"-16)
  • 1 x USB 2.0 Cable (A-Male to Mini-B)
  • 1 x PSU 2-Pin Connector to 18W AC Adapter 6ft cable
  • 1 x HDMI 18in Cable (Type A to Type A)
  • 1 x SDI (BNC to BNC) Cable 10 inch